Taylor Retirement Farm Equipment Catalog
BIDDDING BEGINS TO CLOSE - March 23rd 2026 @ 6:00PM
LOADOUT WILL BE MARCH 26th, 2026 by appointment only. 9:00AM-4:00PM
All buyers with Invoices over $1500.00 must make payment arrangements with in 24hrs after the auction closes.
Invoices under $1500.00 will be charged to the credit card on file unless previous arrangements have been made.
TO VIEW ITEMS: Contact Jeff Pittman @ 816-262-8753 to make arrangements.
This equipment is sold AS IS, WHERE IS, with all faults, known and unknown, visible or hidden, without any warranties or guarantees of any kind, either express or implied, including but not limited to any warranty of merchantability or fitness for a particular purpose.
Owner(s) and West Central Auction Company make no representations or warranties regarding the condition, safety, operability, suitability, or fitness of this vehicle for any intended use. Neither party shall be liable for any loss, damage, injury, or expense arising from the sale or subsequent use of this vehicle.
The buyer is solely responsible for conducting their own inspection and due diligence prior to bidding. By submitting a bid and completing the purchase, the buyer acknowledges and accepts the vehicle in its present condition and assumes all risks and responsibilities associated with ownership, operation, transport, and any repairs or defects, whether known or unknown, existing at or after the time of sale.
All sales are final.
VIDEO BELOW
YEAR: 1994
MAKE: Ford
MODEL: 8770 (70 Genesis Series)
SERIAL: D402841
ENGINE: 7.5L 6 cyl, 190hp
FUEL: Diesel
TRANSMISSION: 16 speed full power shift
DRIVE: MFWD
HOURS: 6142 (engine work @ 5835hrs)
PTO: 1000 rpm
TIRES: 4 New Rear tires put on at approx 6000 hours
OWNER: M Taylor
AC/Heat working
Runs and operates as it should,
Has been kept inside when not in use.
REPAIRS: Pistons, Rings, Lower bearings, Head work, Injectors rebuilt, work by Summa Implement 12/2025 (engine work @ 5835hrs)
LF MFWD Hub leaking-repaired 02/09/26 work by Oakley Ag Repair
VIDEO BELOW
YEAR: 1974
MAKE: Ford
MODEL: 4000 Utility
SERIAL: C415995
ENGINE: 3.3L 3 cyl 57hp
FUEL: Diesel
TRANSMISSION: 8 speed
DRIVE: 2WD
HOURS: 8853
PTO: 540 rpm
TIRES: Good, Fluid in Rear tires for weight
OWNER: M & R Taylor
New Battery 12/25
Has been kept inside when not in use.
REPAIRS NEEDED: Power steering pump is leaking into crankcase and will need to be replaced. It has been resealed two times already.
Hydraulic pump may need work (seems weak owner stated)
Runs and Operates
MAKE: Land Pride
MODEL: RCR 3515
SERIAL: 336669
WIDTH: 15ft, Wing fold
PTO: 540 rpm
TIRES: Laminated
OWNER: M & R Taylor
Has been kept inside when not in use.
VIDEO BELOW
YEAR: 1968
MAKE: Chevrolet
MODEL: C-50 Grain Truck
BED: 14’x8’ Metal floor w/wood side boards, Hoist
VIN: CE538S160502
ENGINE: 350 V-8
FUEL: Gas
TRANSMISSION: 4 Speed w/two speed
DRIVE: Dual Rear Wheel
MILES: 07404 showing (However, no warranty is expressed or implied as to its accuracy)
OWNER: M Taylor
TITLE: Missouri
Runs and operates
Has been kept inside when not in use
WATER TANK AND HOSE IS NOT INCLUDED WITH THE TRUCK
Large capacity plastic tank suitable for liquid storage. Marked with gallon and liter graduations. Includes fill cap and outlet fitting.
Owner: M Taylor
MAKE: Kewanee
MODEL: 1020
SERIAL:
WIDTH: 20ft, Hyd Wing fold
OWNER: M Taylor
Has been kept inside when not in use.
MAKE: WIL-RICH
MODEL: 10FCW-4B w/harrow attachment
SERIAL: 584
WIDTH: 20ft, Hyd Wing fold
OWNER: M Taylor
Has been kept inside when not in use.
MAKE: Big Dog
MODEL: S-8
CAPACITY: 8yd
WIDTH: 7’6” Cut
OWNER: M Taylor
Has been kept inside when not in use.
MAKE: John Deere
MODEL: 210 Disk (T0210)
SERIAL: 028530
WIDTH: 16ft
OWNER: M & R Taylor
Has been kept inside when not in use.
Has been stored inside.
Owner: M Taylor
300bu. Four-wheel gravity flow wagon w/extensions
Owner: M Taylor
400bu. E-Z Trail 400 farm wagon.
Serial number 1384B051910Z.
Owner: M Taylor
Huskee 200bu.
Model 165 Gravity Wagon.
Cracked/Broken spindle on front left(See photos)
Owner: M & R Taylor
Four-wheel farm wagon with wood box and hoist.
Owner: M & R Taylor
31' x 10" Mayrath Grain Auger
PTO: 540
Used last fall harvest
Stored inside
Owner: M Taylor
MAKE: Blu-Jet
MODEL: 13 Knife Anhydrous Applicator with Ravens Super Cooler/Ravens 440 Controller
Coulters and cover disks good
WIDTH: 30” rows
OWNER: Consigned by Delvon Hannah
MAKE: Ferguson
MODEL: B Series Drain Ditcher
WIDTH: Approx 16” blade
PTO: 540
HITCH: 3pt
Stored inside
OWNER: M & R Taylor
Mounts to gravity flow wagon and was used as a seed tender.
Stored inside
OWNER: M & R Taylor
PTO: 540
HITCH: 3pt
AUGER: Approx 9"
Stored inside
OWNER: M Taylor
MAKE: Ford
MODEL: I0I Plow
WIDTH: 3-14”
HITCH: 3pt
Stored inside
OWNER: M & R Taylor
MAKE: BMB
MODEL: EB-8, 8ft
WIDTH: 8ft
HITCH: 3pt
Stored inside
OWNER: M & R Taylor
HITCH: 3pt
Stored inside
OWNER: M & R Taylor
Fuel storage tank manufactured by S.O. Co. in 1946. Includes attached hose and stand. Measures approximately 70" in length and 36" in diameter.
OWNER: M & R Taylor
MAKE: Hardi
MODEL: Ranger 550
WIDTH: Approx 60ft boom
HITCH: Trailer type
With HC 5500 monitor and operators manual
Stored inside
OWNER: M & R Taylor
MAKE: REM 2500 Heavy Duty Grain Vac
MODEL: REM 2500
PTO: 1000
HITCH: Trailer type
SERIAL: 8105
Hour meter does not work and does not display correct hours.
Used last 1/2026
Stored inside
OWNER: M Taylor
MAKE: Blu-Jet
MODEL: 5 Knife Sub-Tiller II
SERIAL: 2508
HITCH: 3pt
Hour meter does not work and does not display correct hours.
Stored inside
OWNER: M Taylor
VIDEO BELOW
YEAR: 1994
MAKE: AGCO Gleaner
MODEL: R52
SERIAL: R5254135A
ENGINE: Duetz 6cyl air cooled
FUEL: Diesel
TRANSMISSION: Hydrostatic drive
DRIVE: 2WD
HOURS: Engine- 4185, Seperator- 2920 (hours are correct)
TIRES: Good,
Has been kept inside when not in use.
Motor and Hydrostats seem to work fine. New head gaskets 8-9yrs ago.
AC/Heat worked last fall,
Runs and Operates, Owner ran 300 acres thru this machine fall of 2025
Owner bought in 2007
2 WAY RADIO IS NOT INCLUDED
REPAIRS NEEDED: Separator and components are well worn and will need work. Motor uses about a quart of oil a day. Hopper full light stays on.
OWNER: Consigned by Daniel Brewer-call for information or to look at it. 816-262-9763
MAKE: AGCO/Gleaner
MODEL: 500 20ft Grain Platform
SERIAL: 2042722F
FIT: Gleaner R52
Stored inside
Used last Fall of 2025
Head does have wear and signs of wear.
New bearing ring on left side of reel with in the last 2 years.
PLATFORM ONLY (TRAILER NOT INCLUDED)
OWNER: Consigned by Daniel Brewer-call for information or to look at it. 816-262-9763
MAKE: Maurer Mfg. Inc
MODEL: 20ft Header Trailer
Stored inside
Used last Fall of 2025
TRAILER ONLY
OWNER: Consigned by Daniel Brewer-call for information or to look at it. 816-262-9763
Campbell Hausfeld 4 Cast Iron Air Compressor. Sold for parts.
OWNER: M & R Taylor
Manual shop press with a 12-ton capacity. OWNER: M & R Taylor
Lincoln Electric Lincwelder AC-225-S arc welder with amperage dial and electrical cord. OWNER: M & R Taylor
Includes a metal Penncraft tool box with an assortment of tools. OWNER: M & R Taylor
Grouping of various hand saws with wooden handles. Includes a circular saw blades. OWNER: M & R Taylor
Includes brands such as Easco, Allied, and S-K Tools. Sizes include 1 1/2 inch, 1 1/4 inch, 1 1/8 inch, and 15/16 inch. OWNER: M & R Taylor
Includes Challenger, Craftsman, and T A Tools open end wrenches in various sizes. OWNER: M & R Taylor
Assortment of various size wrenches including Craftsman, S-K, and Challenger brands. OWNER: M & R Taylor
Includes metal oil cans and funnels. OWNER: M & R Taylor
Includes assorted sizes and styles of wrenches. OWNER: M & R Taylor
Collection of assorted hammers including claw hammers and mallets, along with related tools. Some handles are wood and some are fiberglass. OWNER: M & R Taylor
Includes metal working tools, cutting tools, pliers, and automotive-related items. OWNER: M & R Taylor
Collection of steel chisels of various sizes and shapes, stored in a blue metal container. OWNER: M & R Taylor
Includes a Sears 1/4-inch and 3/8-inch socket wrench set in a red case, along with a box containing metal hooks. OWNER: M & R Taylor
This lot contains three metal pry bars. OWNER: M & R Taylor
Record Sheffield bench vise with blue accents and threaded shaft. "Record" is embossed on the top. OWNER: M & R Taylor
Includes a Black & Decker 7 1/4" Deluxe Saw and a Black & Decker Variable Speed Jig Saw. Working OWNER: M & R Taylor
Includes balancer puller, grinders, gates heating tape, and automotive tools. OWNER: M & R Taylor
Coleman Powermate professional spray gun in original box with paperwork. OWNER: M & R Taylor
Sioux 6" Ball Bearing Grinder manufactured by Albertson & Company, Inc. OWNER: M & R Taylor
Includes a metal tool box with assorted tools, including drill bits, hand tools and other tool accessories. OWNER: M & R Taylor